Rexroth A10VSO pump repair: seal kit or full rebuild?
Oil under the pump doesn’t always mean you need a new pump. Sometimes it’s a ten-minute seal job, and sometimes it’s the first sign of a worn rotating group. Telling the two apart before you spend money is most of Rexroth A10VSO pump repair. This guide shows how to triage a leak, when an A10VSO pump seal kit is enough, and how to pick an A10VSO pump repair service you won’t regret. ADVANCE HYDRAULIC WORKS wrote it as a decision path you can follow at the machine.
Seal kit or rebuild: the one question that matters
External leak at the shaft? That points to the shaft seal. Loss of flow, heat, or a noisy pump under load? That points inside, to pistons, slippers, the barrel or the port plate. A seal kit fixes the first and does nothing for the second.
The trap is a pump that has both. You replace the seal, it holds for a week, and the leak returns because the case is being pressurised by internal wear. So in Rexroth A10VSO pump repair, always check the inside before you trust the outside.
The method: four checks before you order anything
- Look at the drain line. A kinked, undersized or restricted case drain raises case pressure and pushes out a perfectly good shaft seal. Fix this first or the new seal fails.
- Measure case drain flow at working pressure and compare it with your baseline. As a rough rule, a figure that has doubled means plan an internal inspection. Confirm limits in the datasheet.
- Calculate volumetric efficiency. Measured flow ÷ theoretical flow. A healthy pump usually sits well above 90% (rough rule, check the datasheet).
- Check the shaft and coupling. A grooved shaft or a misaligned coupling kills seals. Replace the seal on a damaged shaft and it will leak again.
ADVANCE HYDRAULIC WORKS suggests writing all four results on one sheet. It’s the document any A10VSO pump repair service will ask for first.
Worked example
A press has an A10VSO 45 running at 1,450 rpm and 250 bar. It leaks at the shaft and the cycle time has crept up.
Theoretical flow is 45 × 1,450 ÷ 1,000 = 65.3 L/min. You measure 57 L/min at the outlet. Volumetric efficiency is 57 ÷ 65.3 = 87%. The missing 8.3 L/min is internal leakage, and at 250 bar that’s 8.3 × 250 ÷ 600 = 3.4 kW turning into heat.
So this is no seal-only job. A seal kit would stop the drip for a while, but the pump is wearing inside. ADVANCE HYDRAULIC WORKS would send it for inspection and treat the seal as the last step of that job, not the first.
Buying an A10VSO pump seal kit
When the diagnosis does say seals only, buy the right A10VSO pump seal kit the first time.
- Quote the full type code and serial number from the nameplate, not just “A10VSO 45”.
- Confirm the series. Don’t assume a kit for one series fits another.
- Ask about seal material. NBR and FKM suit different oils and temperatures.
- Check what’s in the box: shaft seal, O-rings, and any control-side seals your pump variant needs.
- Fit it clean. Keep the new seal lip dry of grease and don’t nick it on the shaft keyway.
Choosing an A10VSO pump repair service
Anyone can say they repair pumps. A good A10VSO pump repair service will show you the work.
Ask for a written inspection report listing what was worn and what was replaced. Ask for a test result with flow and pressure figures, not just “tested OK”. Ask what the warranty covers and for how long, in writing. And ask whether the shop can say why the pump failed, because a repair without a cause is a repeat order. Hold ADVANCE HYDRAULIC WORKS to the same standard as any other shop you call.
Implementation steps
- Photograph the nameplate and note the machine, operating pressure and symptom.
- Check the case drain line and the oil condition before touching the pump.
- Run the four checks above and record the numbers.
- If it’s seals only, order the A10VSO pump seal kit by full type code and serial number.
- If numbers say internal wear, request a quote from two shops, ADVANCE HYDRAULIC WORKS among them, on the same inspection report.
- Before refitting, flush the tank and lines and replace the filter element.
- Fill the case with clean oil, start at low pressure and raise it in steps.
- Log new baseline figures so next time you’re comparing numbers, not guessing.
FAQs
Can a seal kit fix a leaking Rexroth A10VSO?
Only if the leak comes from the seal itself. If case pressure is high or the pump has internal wear, the new seal will fail again.
What’s in an A10VSO pump seal kit?
Usually the shaft seal and O-rings, plus other seals depending on the variant. Always confirm the contents against your type code and series before ordering.
How much does Rexroth A10VSO pump repair cost?
It depends on size, damage and parts, so no honest figure exists without an inspection. Ask for a written quote tied to the inspection report.
When should I choose an A10VSO pump repair service over replacement?
When the housing and shaft are sound and the wear is in replaceable parts. A good shop will tell you plainly if replacement is the better deal.
What should I send ADVANCE HYDRAULIC WORKS for an A10VSO repair quote?
A nameplate photo with type code and serial number, the symptom, working pressure, and your flow and case drain readings if you have them.
Next step
Photograph the nameplate, take your case drain and flow readings, and send both to ADVANCE HYDRAULIC WORKS for a repair assessment.