A10VSO 18 DFR/31R-PPA12O30: This pump differs from most pumps of size 18 DFR. If you do not check this code carefully, you may be presented with a pump that is different to what you ordered. Regardless of whether it is referred to as BOSCH REXROTH A10VSO 18 DFR/31R-PPA12O30 or AXIAL PISTON PUMP A10VSO 18 DFR/31R-PPA12O30, the checks remain the same. To allow quick identification, ADVANCE HYDRAULIC WORKS have put together this information. A10VSO 18 DFR/31R-PPA12O30: A10VSO: Variable displacement open circuit axial piston pump 18: Size. Displacement of 18cm³ per revolution. This is equivalent to a flow rate of approximately 26.1L/min at 1450rpm with maximum swivel. DFR: Pressure and flow regulation based on load sensing function. Therefore, a load sensing signal must be sent to port X. 31: Series. R: Rotation direction. Clockwise. PPA12O30: Seals, shaft, flange, connections and through drive. In Rexroth’s coding system, the first letter refers to seal material. Typically, P refers to NBR seals. However, the last part of this code differs. From just looking at the code, we cannot determine what information this last part provides. Therefore, a supplier should never attempt to guess. To understand what this last part indicates, refer back to the ordering information within the data sheets of this series. ADVANCE HYDRAULIC WORKS will never guess information in this area of the code. BOSCH REXROTH A10VSO 18 DFR/31R-PPA12O30: While the heading of the item details that it should have been manufactured by this brand, confirmation is required. Within the image of the name plate, ensure that it clearly shows Rexroth branding and full part code. Additionally, ensure that it shows the part number. As this part code has an unusual suffix, it is particularly important to confirm that this is correct. An exact specification can be determined from the Rexroth material number. Ensure that in your quotation, the part number is shown with the part code, and that this matches with the image. As we cannot assume what part number is used for this specification, you should refer to the part number on your name plate. If ADVANCE HYDRAULIC WORKS cannot match up the part code to their part number, they will delay the order. AXIAL PISTON PUMP A10VSO 18 DFR/31R-PPA12O30: Suffix In this part code, the suffix is O30 (letter ‘O’ and numbers 3 and 0). Most of the time, pumps of this size will have numerical suffixes, for example N00 (double zero). The letter O and the number 0 can appear very similar in a wide range of fonts and stamped name plates. This could be a problem. If in the quotation the suffix is PPA12030 (double zero) compared to PPA12O30 on your name plate, just one character is different. This could mean that it is a different specification, or possibly not. Zoom into the name plate image and compare with the ordering information in the data sheet. Double check with the part number. If you are unsure, we recommend that you write the part code in capital letters on your sheet, and add a note of ‘Letter O’. This means that if it is re-typed in the future, it will be clear that it is a letter rather than a number. Checks: Check all characters. In particular check for letter ‘O’ and 0. Compare the suffix with the ordering information in the data sheet. Ensure that the part code and part number match with those on the name plate, and with each other. Check that the control type is correct. As this is a DFR control, a load sensing signal must be provided at port X. The power in kW can be calculated by (flow x pressure)/ (600 x efficiency). ADVANCE HYDRUALIC WORKS complete all 4 checks for every quotation they receive, including quotations for themselves. Example: A10VSO 18 DFR/31R-PPA12O30 and PPA12030 (with 0) are different by one character. Until the part number matches with the nameplate, they should be treated as different pumps. Send a picture of the nameplate, and the nameplate number, to each seller. Another seller has a pump ending in ‘N00’, but has noted that it is ‘the same 18 DFR, in stock’. As the end of the part number differs, there may also be differences in the through drive and other options. Unless the datasheet and drawing from the machine match up, this can not be considered a direct replacement. Drive Check Flow: 18 x 1,450 / 1,000 = 26.1L/min. Power: 26.1 x 250 / 600 = 10.9kW. Shaft power will be around 12.1kW (assuming 90% efficiency, check datasheet). An 11kW motor would be undersized. Therefore to be safe, choose the standard 15kW motor. Implementation steps: Take a picture of the nameplate. Ensure you can see the end of the part number clearly, and take note of the code, in uppercase. Note whether the unclear character is an O or 0, and take note of the part number. Compare the post-hyphen block to the order code in your datasheet. Ensure that a load sense signal is coming from the machine into port X. Perform the drive check. Send the same message to 2 or 3 suppliers (include ADVANCE HYDRAULIC WORKS). Ensure code and part number match the nameplate exactly. Compare responses line by line. Be sure to check the whole code is identical between suppliers. When you receive the pump, check that the nameplate matches. Drain the tank and pipework. Top up clean oil in the casing via the casing drain port. Increase pressure gradually from low pressure. (ADVANCE HYDRAULIC WORKS recommend noting base readings on the service tag of the machine). FAQS: 1.What is A10VSO 18 DFR/31R-PPA12O30? It is a 18 sized, variable displacement pump from Rexroth. DFR means it has DFR controls. Series 31, and turns in a clockwise direction. The PPA12O30 gives information on seals, shaft, flange, ports and through drive. Compare to the order code in the datasheet. 2.Is BOSCH REXROTH A10VSO 18 DFR/31R-PPA12O30 the same as a pump ending in N00? No. As the end of the part number is different, there could be differences in the through drive and other options. These should be considered to be different constructions, until confirmed as the same by matching part numbers in the datasheet. 3.In AXIAL PISTON PUMP A10VSO 18 DFR/31R-PPA12O30 is the O a letter or 0? In the guide, it is an O. Always double check from the nameplate as they are very similar looking characters, and switching them will give a different code. 4.What does the part number tell me? It tells me the specific configuration of the product. Ensure you include both the type code and part number, and that they match the nameplate. 5.What information should I include in my message to ADVANCE HYDRAULIC WORKS? A picture of the nameplate (including type code and part number), model of the machine, operating pressure and motor speed. Next Step Take a picture of the nameplate on your pump. Ensure the end of the code can be seen clearly. Send this, along with the machine model and operating pressure, to ADVANCE HYDRAULIC WORKS.