Rexroth A10VSO 28 Supplier/Dealer/Distributor There are 8 different pumps with the same type code of A10VSO 28. They have different material numbers, varying weights (17.8kg to 20kg) and 3 different control types. This is because of how the pump is listed. You’ll need to look for the material number to get the exact pump. We suggest you ask a supplier who understands the difference. Advance Hydraulic Works do repairs and supply of hydraulic pumps from Delhi NCR. Please ask us the same question. Pump specification The pump has a nominal pressure of 280bar and a nominal speed of 3,000rpm. The data sheet shows it as a swashplate, variable open circuit pump with a nominal pressure of 280bar and a max pressure of 350bar. The sizing number shows it will displace 28cm³ per revolution. The listing on the seller page shows flow of approximately 84 litres per minute at 3,000rpm and 125Nm Torque at 280bar. It also shows a maximum speed of 3,600rpm. The smaller size of 18 will run at 3,300rpm full displacement and 3,900rpm reduced displacement (see data sheet excerpt). The size 28 seems to be the same and will therefore run at 3,000rpm full displacement. 3,600rpm only occurs when the pump is destroked. This can be checked by looking at your data sheet. A seller claiming it will run at 3,600rpm hasn’t looked at the data sheet. Multiple pumps with the same type code Listings show pumps with the following: A10VSO 28 DFR1/31R-PPA12N00-SO410 (material number R910946322) 18kg A10VSO 28 DFLR/31R-PPA12N00 (material number R902402636) 19kg A10VSO 28 DFLR (material number R910936130) 20.05kg Many variations using prefixes (AL/AE etc.) The data sheet shows approximately 18Kg with no through drive and 19.3kg with through drive. Some of the weight differences come from having a through drive but the others are bespoke builds. The control types differ. One listing shows DFR1 but has a DRS control. Another shows DFR1 but has a DRSC control. Take the type code from the title and then ask what material number refers to. Rexroth A10VSO 28 Supplier This can be any importer, trader or reseller. Its fine, but ask what material number the exact unit has. Ask what the suffix/prefix refers to. We fall into this category so ask us. A10VSO 28 Pump Dealer Usually supplies to workshops or factories. Will often get their pumps from a distributor. Ask what they get their pumps from (in writing), what material number and weight. A10VSO 28 Pump Distributor Should have an authorised appointment from the manufacturer. Ask to see the document and verify with the manufacturer. An genuine distributor will be able to tell you why there are different material numbers for the same type code. Type Code Ensure you know the full type code from your nameplate. Material Number:Look for the R number and ask each seller to state what it is. Weight:Make sure it matches the weight shown on the data sheet for your setup. Verification:Ask what the source is, condition and a picture of the plate. Worked Example The size 28 will displace 28 x 1,800 / 1,000 = approx 50 litres per minute. At 250bar the hydraulic power will be 250 x 50 / 600 = approx 21kW. At 280bar the Torque will be 28 x 280 / 62.8 = approx 125Nm. Which matches the data sheet. 3 Sellers state they have the same type code. Seller A states what material number it is, 18kg no through drive and a picture of the plate. Seller B states what type code it is and says its the same as original. Seller C says it weighs 20kg but doesn’t state what material number. The weight difference should make you question what they have. Are they selling a through drive version, bespoke build? If your pump doesn’t have a through drive but theirs does the mounting will be different. The material number will help give you an accurate match. The calculations below are just to give an example, use the current data for your pump. Implementation steps Take photos of the pump, its nameplate, and the port. Write down the overall type code and fabric number. Take a look at your power speed, working pressure, and whether the pump is running a 2d pump. Send the whole to Advance Hydraulic Works and at least one other supplier. Ask each salesperson to cite material variations, manipulation, weight, and any convictions in the writing. Ask in writing for supplies, status and guarantees. Check any “accredited” claims with the manufacturer. Compare the delivered plate with your order, then start healthy, primed and at low pressure. FAQs What is the Rexroth A10VSO 28? For open circuits, a 28 cm3 variable axial piston pump in line with the revolution, rated at 280 bar and most of the nominal 350 bar. A10VSO 28 Why do lists show extraordinary weights? Loads are exchanged through drives and unique builds. The statistics sheet gives about 18 kg without through pressure and 19.three kg with one. How do I discover a genuine A10VSO 28 pump dispenser? Ask for a written appointment letter and check with the manufacturer. Then ask the vendor to quote your material variety. Which is the best A10VSO 28 pump provider? One that demands your entire compassionate code and range of fabric can provide interpretation of beliefs and burdens. A supplier who only asks for quantity doesn’t study the pump. Does Advanced Hydraulic Works A10VSO take 28 inquiries? Yes. Send plate pics, kind code and fabric quantity to Advance Hydraulic Works, and ask for approximate supply, condition and warranty before committing. Your next step Photograph the nameplate, copy the type code and the wide variety of fabrics, and ship both to Advance Hydraulic Works. Ask them to take off their ribs and ask each other s