Description

Danfoss OMR 80 dealer, supplier or distributor in India: a channel map and a spec sanity check Indian listings for this motor look confident. They name six cities, promise “completely interchangeable” and show a spec table. Then you read the table and one number is off by a factor of ten. That’s why this guide does two things. It maps who can actually sell the Danfoss OMR 80 in India, and it gives you a quick sanity check that catches careless sellers. Advance Hydraulic Works supplies hydraulic motors, pumps and valves to factories and plants across India, and this is how we’d walk a buyer through it. The motor: real numbers A reseller datasheet gives the OMR 80’s geometric displacement as 80.3 cm³, with a maximum speed of 750 rpm (940 intermittent), maximum torque of 195 N•m (220 intermittent, 270 peak), power of 12.5 kW, a pressure drop of 175 bar (200 intermittent, 225 peak) and a maximum flow of 60 litres per minute. The same listing describes a 25 mm straight shaft with an 8 mm key, a 2-hole SAE-A flange and G1/2 side ports. Danfoss’s own catalogue lists the OMR sizes 50, 80, 100, 125, 160, 200, 250, 315 and 375, with the 80 at 80.3 cm³. Those are the figures to hold sellers against. The spec sanity check An Indian seller’s table for this motor lists a continuous torque of 19.5 N•m next to 80.3 ml per revolution and 175 bar. Run the numbers. Theoretical torque is about 80.3 × 175 ÷ 62.8, roughly 224 N•m. Real torque is lower, about 195. A table that says 19.5 has a decimal slip. It’s a small error, but it tells you something. If a seller’s page has an uncorrected tenfold mistake, ask how carefully they check what they ship. This sanity check takes thirty seconds and works on any spec table. Who makes it now? The OMR range isn’t produced by Danfoss any more. Danfoss set up White Drive Motors & Steering as a stand-alone business, because it had to divest the line to get approval for its Eaton Hydraulics acquisition. Interpump Group then agreed to buy the unit from Danfoss. A reseller says the motors from White replace the OMR orbital motors produced by Danfoss. So for a seller’s authorisation claim to mean anything, it should name a maker. For the OMR 80, that may be White, not Danfoss. Danfoss OMR 80 dealer: what to ask A Danfoss OMR 80 dealer usually sells to workshops and factories, often buying from a distributor. Ask which maker or distributor supplies it, and ask for that in writing. A dealer’s promise is only as good as its source. Danfoss OMR 80 supplier: the loosest label A Danfoss OMR 80 supplier can be any importer, trader or reseller. That’s fine, as long as they say what they are. Advance Hydraulic Works sits in the supplier group, and we’d rather you check our answers than trust our label. Danfoss OMR 80 distributor in India: the strongest claim A Danfoss OMR 80 distributor in India should hold an appointment from the maker for the territory. Danfoss publishes an authorized partner network with a tool for finding your distributor, but that covers Danfoss’s own lines. For the OMR, you’d also check with the current maker. Be wary of the phrase “completely interchangeable with Danfoss original”. That’s a claim by sellers of replacement motors, not proof. Ask for the maker, the part number and a plate photo. The method: map, quiz, proof Map. Ask which channel the seller buys from: maker, distributor, importer or replacement maker. Quiz. Ask the five numbers: displacement, speed, torque, pressure and flow. Compare with the datasheet. Proof. Ask for an appointment letter, source documents and a plate photo. A worked example Say you get three quotes. Seller A answers the five numbers correctly, names its source and sends a plate photo. Seller B quotes the 19.5 N•m torque from a copied table and says “same as original”. Seller C names a price and nothing else. Score one point per correct, evidenced answer, out of eight: five numbers, source, appointment and plate. A might score eight. B scores three. C scores zero. If B is cheaper by 10%, ask whether that saving covers a wrong motor and a second freight bill. A scoring sheet makes the answer obvious. This is an illustrative method, not a rule. Implementation steps 1. Photograph the old motor’s nameplate, shaft and flange before removal. 2. Write down the model code, displacement and any old part number. 3. Measure the shaft and note the port sizes. 4. Send the details and the quiz to Advance Hydraulic Works and at least one other seller. 5. Record every answer in one table. 6. Ask for source, condition and warranty in writing. 7. Check any “authorised” claim with the maker. 8. Compare the delivered motor’s plate with your order, then fit it and run it unloaded first. The usual mistakes are believing a copied spec table, trusting a city list and skipping the plate check. FAQs Who is a Danfoss OMR 80 dealer in India? A dealer sells to end users, often buying from a distributor. Ask which source it buys from, in writing, and check any authorisation with the maker. What does a Danfoss OMR 80 supplier do? A supplier is a looser term that includes importers and traders. Ask where the motor came from, its condition and who gives the warranty. How do I find a real Danfoss OMR 80 distributor in India? Ask for a written appointment and check it with the maker. For OMR motors, check with White Drive Motors & Steering as well as Danfoss. What are the specs of the OMR 80? About 80.3 cm³, 750 rpm, 195 N•m, 175 bar and 60 litres per minute continuous. Check the current data sheet for your exact version. Does Advance Hydraulic Works take enquiries for this motor? Yes. Send the nameplate photos, model code and working pressure to Advance Hydraulic Works, and ask about source, condition and warranty before you commit. Your next step Photograph the nameplate, run the quiz and send everything to ADVANCE HYDRAULIC WORKS You’ll see what we know before you commit, and you can put the same questions to every other seller.